PROseal
PROseal is a premium quality high velocity water based duct sealant.
FIBERseal is a premium quality high velocity duct sealant with fiber reinforcement.
SPECIAL CHARACTERISTICS
- UL Classified
- Permanently Flexible
- Non-Flammable
- Exceptional Workability
- Will Not Drip or Sag
- Low Brush Drag and Spreadability Reduces Labor Cost
- Low Shrinkage
- Excellent Adhesion to Metal
- Mild Odor
- Indoor or Outdoor Use
- Superior Sealing Strength
- Conforms to Requirements of NFPA 90A and 90B
- Mildew Resistant
- No VOC's
UNDERWRITERS LABORATORIES, INC. CLASSIFIED CAULKING AND SEALANTS SURFACE BURNING CHARACTERISTICS
FIBERSEAL Duct Sealant applied to inorganic reinforced cement board
- Flame Spread 5
- Smoke Developed 5
Tested as applied in two 2" wide strips 8" on center (coverage 18 percent of the exposed test samples area) at a coverage rate of 250 sq. ft. per gal. Flash point of finished sealant, closed cup. No flash to boiling.
PROSEAL Duct Sealant applied to inorganic reinforced cement board
- Flame Spread 5
- Smoke Developed 5
Tested applied in two 2" wide strips 8" on center (coverage 18 percent of the exposed test sample area) at a coverage rate of 250 sq. ft. per gal. Flash point of finished sealant, closed cup. No flash to boiling
TYPICAL PHYSICAL PROPERTIES AND TECHNICAL INFORMATION
PROSEAL BASE: Synthetic latex emulsion
FIBERSEAL BASE: Synthetic latex emulsion with fiber reinforcement
- COLOR: Gray
- TYPE: Water Base
- WEIGHT: 11+/- .2 lbs.per gallon
- SOLID CONTENTS: 66% +/- 2%
- VISCOSITY: 350,000 c.p.s.
- APPLICATION TEMPERATURE: 35°F to 110°F
- SERVICE TEMPERATURE: -25°F to 175°F
- STORAGE TEMPERATURE: 40°F to 85°F
- FLAMMABILITY: Non-flammable in both wet and dry state
- FLASH POINT: No flash to boiling
- MILDEW RESISTANCE: Excellent
- WATER RESISTANCE: Excellent
- FREEZE THAW STABILITY: 5 cycles
- COVERAGE: 50 sq. ft./gal. at 1/16", 25 sq. ft./gal. at 1/8"
- ODOR: Mild (wet) None (dry)
- SHELF LIFE: 1 year (unopened container)
- CURED SEALANT: Tough and permanently flexible
- DRY TO TOUCH: 1 hour (approximate)
- CURE TIME: 24 to 72 hours (depending on humidity, application and temperature)
PACKAGING & ORDERING INFORMATION
PART NUMBER | DESCRIPTION | QTY & WEIGHTS | PART NUMBER | DESCRIPTION |
PROSEAL T | PROSEAL tubes | 25-10.5 oz. tubes @ 25 lbs./cs | FIBERSEAL T | FIBERSEAL tubes |
PROSEAL 1 | PROSEAL 1-gal. | 4-1 gal. pails @ 50 lbs./cs | FIBERSEAL 1 | FIBERSEAL 1-gal. |
PROSEAL 5 | PROSEAL 5-gal. | 1-5 gal. pail @ 64 lbs./pail | FIBERSEAL 5 | FIBERSEAL 5-gal. |
PROSEAL 55 | PROSEAL 55-gal. | 55 gals @ 700 lbs./drum | FIBERSEAL 55 | FIBERSEAL 55-gal. |
RECOMMENDED USES
To seal to metal joints against air leaks in low, medium and high pressure duct systems.
DIRECTION FOR USE
Surface Preparation: For good brushability, store at room temperature at least 24 hours before applying. Surfaces should be clean, dry and free of oil, grease and any other foreign material.
Application: Use a brush, caulking gun or pump. FIBERSEAL should be applied to duct connections according to all applicable SMACNA standards. Apply to the inside of female fittings and outside of male fittings. Assemble the joint. Brush sealant over the assembled joint and screws with a 2" to 3" wide band. Assembly should cure for 24 to 72 hours before pressure testing the system.
Pressure Rating: FIBERSEAL is recommended for use in HVAC duct systems which do not exceed 15" water column pressure. Fiber glass mesh scrim should be used to reinforce all systems with pressures in excess of 15" and where needed to bridge gaps in ductwork joints which may exceed 1/4".
Precautions: Do not thin. Do not apply below 35° F. Do not permit installation to go below freezing for 48 hours.
Clean-up: Use warm soapy water to clean up sealant while it is still wet.
AVAILABILITY
All Ductmate products are available through its global manufacturing and distribution network.
| 
