EZ-seal
EZ-seal is an industrial grade duct sealant with fiber reinforcement.
SPECIAL CHARACTERISTICS
- UL 181B-M Listed
- Conforms to NFPA 90A and 90B
- Flexible
- Non-Cracking Formula
- UV Resistant
- Non-Flammable
- Will Not Drip or Sag
- Minimal Shrinkage
- Excellent Adhesion to Metal
- Mild Odor
- Weather Resistance
- Indoor or Outdoor Use
- Mildew Resistant
- No VOC's
UNDERWRITERS LABORATORIES, INC. CLASSIFIED CAULKING AND SEALANTS SURFACE BURNING CHARACTERISTICS
EZ-SEAL Duct Sealant applied to inorganic reinforced cement board
- Flame Spread 5
- Smoke Developed 0
Tested as applied in two 2" wide strips 8" on center (coverage 22.2 percent of the exposed test samples area) at a coverage rate of 25 sq. ft. per gal. Flash point of finished sealant, closed cup. No flash to boiling.
TYPICAL PHYSICAL PROPERTIES AND TECHNICAL INFORMATION
BASE: Synthetic latex emulsion with fiber reinforcement
- COLOR: Gray
- TYPE: Water Base
- WEIGHT: 10.9+/- .2 lbs.per gallon
- SOLID CONTENTS: 62% +/- 2%
- VISCOSITY: 400,000 c.p.s.
- APPLICATION TEMPERATURE: 35°F to 110°F
- SERVICE TEMPERATURE: -25°F to 200°F
- STORAGE TEMPERATURE: 35°F to 110°F
- FLAMMABILITY: Non-flammable in both wet and dry state
- FLASH POINT: No flash to boiling
- FREEZE THAW STABILITY: 5 cycles
- COVERAGE: 25 sq. ft./gal. at 1/16", 50 sq. ft./gal. at 1/32"
- ODOR: Mild (wet) None (dry)
- SHELF LIFE: 1 year (unopened container)
- CURED SEALANT: Tough and flexible
- DRY TO TOUCH: 1 hour (approximate)
- CURE TIME: 24 to 72 hours (depending on humidity, application and temperature)
PACKAGING & ORDERING INFORMATION
PART NUMBER | DESCRIPTION | QTY & WEIGHTS |
EZSEAL T | EZ-SEAL tubes | 25-10.5 oz. tubes @ 25 lbs./cs |
EZSEAL 1 | EZ-SEAL 1-gal. | 4-1 gal. pails @ 50 lbs./cs |
EZSEAL 5 | EZ-SEAL 5-gal. | 1-5 gal. pail @ 64 lbs./pail |
RECOMMENDED USES
To seal to metal joints against air leaks in industrial and residential systems.
DIRECTION FOR USE
Surface Preparation: For good brushability, store at room temperature at least 24 hours before applying. Surfaces should be clean, dry and free of oil, grease and any other foreign material.
Application: Use a brush, caulking gun or pump. EZ-SEAL should be applied to duct connections according to all applicable SMACNA standards. Apply to the inside of female fittings and outside of male fittings. Assemble the joint. Brush sealant over the assembled joint and screws with a 2" to 3" wide band. Assembly should cure for 24 to 72 hours before pressure testing the system.
Pressure Rating: EZ-SEAL is recommended for use in HVAC duct systems which do not exceed 10" water column pressure. Fiber glass mesh scrim should be used when needed to bridge gaps in ductwork joints which may exceed 1/4".
Precautions: Do not thin Do not apply below 35°F. Do not permit installation to go below freezing for 48 hours
Clean-up: Use warm soapy water to clean up sealant while it is still wet.
AVAILABILITY
All Ductmate products are available through its global manufacturing and distribution network.
| 
